• View PDF
    Standard
  •   0091-22-66157017
  •   info@torqbolt.com
    • Home
    2. EN 10269 Grade 42CrMo5-6 (1.7233)

    EN 10269 Grade 42CrMo5-6 (1.7233) Fasteners

    Elevated-Chromium Molybdenum Alloy Steel Bolts, Stud Bolts, Screws, Nuts & Washers in EN 10269 Grade 42CrMo5-6 (1.7233)

    EN 10269 Grade 42CrMo5-6 (1.7233) Fasteners are elevated-chromium molybdenum alloy steel fasteners with superior strength at high temperatures, used in critical pressure vessel, turbine, and refinery bolting applications where demanding mechanical performance is required.

    EN 10269 42CrMo5-6 Chemical composition

    Material designation Chemical composition, % by mass
    Name Number C Si Mn P max. S max. Al tot B Cr Mo Ni V Others
    Steels for quenching and tempering
    42CrMo5-6 1.7233 0,39 to 0,45 ≤ 0,40 0,40 to 0,70 0.025 0.035 - - 1,20 to 1,50 0,50 to 0,70 - - -
    • a Elements not listed in this table may not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All appropriate precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the usefulness of the steel.
    • b A controlled sulphur content of 0,015 % to 0,030 % improves the machinability and is therefore recommended and may be agreed at time of enquiry and order. For weldability, a controlled sulphur content of 0,008 % to 0,030 % is recommended and may be agreed at time of enquiry and order.
    • c For requirements regarding magnetic properties up to a maximum of 0,28 % C.

    EN 10269 42CrMo5-6 Mechanical properties

    Mechanical properties at Room Temperature

    Mechanical properties at room temperature for delivery conditions normally applied for further processing

    Material designation Heat treatment condition a,b Hardness HBW max. Tensile strength Rm MPa max. Reduction in area Z % min.
    Name Number
    42CrMo5-6 1.7233 +S 255 - -
    +A 241 - -
    • a + AC = annealed to achieve spheroidized carbides; + S = treated for cold shearing; + A = soft annealed.
    • b Products made to these heat treatment conditions do not support the Essential Safety Requirements of Directive 97/23/EC, unless other criteria are taken into account, see Annex 1, 7.5 of this directive.

    Mechanical properties at room temperature and at 20 °C of steels in delivery conditions which support the Essential Safety Requirements of Directive 97/23/ECb

    Material designation Heat treatment conditiona Diameter c Proof strength Tensile strength Elongation after fracture Reduction in area Impact energy (ISO-V) at 20°C
    Name Number
    d mm Rp0,2 MPa min. Rm MPa A % min. Z % min. KV2 J min.
    42CrMo5-6 1.7233 +QT d ≤ 100 700 860 to 1 060 16 50 50
    100 < d ≤ 150 640 850 to 1 000 16 50 40
    • a +AT = solution annealed; +C = cold work hardened; +N = normalized; +NT = normalized and tempered; +P = precipitation hardened;
    • +QT = quenched and tempered; +WW = warm worked (see Annex B).
    • b Products made of steel grades and these final heat treatment conditions support the Essential Safety Requirements of Directive 97/23/EC, see Annex 1, 7.5 of this directive.
    • c For rectangular cross-sections "d" will be replaced by "b" (see Figure 1).

    EN 10269 42CrMo5-6 Proof strength

    Minimum 0,2 %-proof strength values at elevated temperature of steels in delivery conditions which support the Essential Safety Requirements of Directive 97/23/EC d

    Material designation Heat treatment conditiona Diameter e d mm Minimum 0,2 %-proof strength Rp0,
    2 in MPa at a temperature (in °C) of:
    Name Number 50 100 150 200 250 300 350 400 450 500 550 600 650
    42CrMo5-6 1.7233 + QT d ≤ 100 681*) 662 639 616 601 585 570 547 516 462 362 223 -
    100 < d ≤ 150 625*) 605 584 563 549 535 521 500 472 422 331 204 -
    • a +AT = solution annealed; +C = cold work hardened; +N = normalized; +NT = normalized and tempered; +P = precipitation hardened; +QT = quenched and tempered; +WW = warm worked (see Annex B).
    • b This steel grade is generally not applied in the creep range.
    • c Values in brackets signify that the steel is not intended for use (and testing) at those temperatures.
    • d Products made to these steel grades and these final heat treatment conditions support the Essential Safety Requirements of Directive 97/23/EC; see Annex 1, 7.5 of this directive.
    • e For rectangular cross sections "d" will be replaced by "b" (see Figure 1).
    • *) Values calculated by linear interpolation.
    Specifications
    Surface Treatments
    Certifications
    About Us
    Questions? Contact us.
    Showcase of our Microsites.
    Satisfaction Survey

    survey

    TUVRheinland CRETIFIED

    © TorqBolt P(Ltd) · Built with in INDIA.