• View PDF
    Standard
  •   0091-22-66157017
  •   info@torqbolt.com
    • Home
    2. EN 10269 Grade 25CrMo4 (1.7218)

    EN 10269 Grade 25CrMo4 (1.7218) Fasteners

    Chromium-Molybdenum Alloy Steel Bolts, Stud Bolts, Screws, Nuts & Washers in EN 10269 Grade 25CrMo4 (1.7218)

    EN 10269 Grade 25CrMo4 (1.7218) Fasteners are chromium-molybdenum alloy steel fasteners with excellent strength, toughness, and fatigue resistance, widely used in pressure vessels, heat exchangers, and high-temperature bolting in petrochemical and power generation plants.

    EN 10269 25CrMo4 Chemical composition

    Material designation Chemical composition, % by mass
    Name Number C Si Mn P max. S max. Al tot B Cr Mo Ni V Others
    Steels for quenching and tempering
    25CrMo4 1.7218 0,22 to 0,29 ≤ 0,40 0,60 to 0,90 0.025 0.035 - - 0,90 to 1,20 0,15 to 0,30 - - -
    • a Elements not listed in this table may not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All appropriate precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the usefulness of the steel.
    • b A controlled sulphur content of 0,015 % to 0,030 % improves the machinability and is therefore recommended and may be agreed at time of enquiry and order. For weldability, a controlled sulphur content of 0,008 % to 0,030 % is recommended and may be agreed at time of enquiry and order.
    • c For requirements regarding magnetic properties up to a maximum of 0,28 % C.

    EN 10269 25CrMo4 Mechanical properties

    Mechanical properties at Room Temperature

    Mechanical properties at room temperature for delivery conditions normally applied for further processing

    Material designation Heat treatment condition a,b Hardness HBW max. Tensile strength Rm MPa max. Reduction in area Z % min.
    Name Number
    25CrMo4 1.7218 +S 255 - -
    +A 212 - -
    +AC - 580 59
    • a + AC = annealed to achieve spheroidized carbides; + S = treated for cold shearing; + A = soft annealed.
    • b Products made to these heat treatment conditions do not support the Essential Safety Requirements of Directive 97/23/EC, unless other criteria are taken into account, see Annex 1, 7.5 of this directive.

    Mechanical properties at room temperature and at 20 °C of steels in delivery conditions which support the Essential Safety Requirements of Directive 97/23/ECb

    Material designation Heat treatment conditiona Diameter c Proof strength Tensile strength Elongation after fracture Reduction in area Impact energy (ISO-V) at 20°C
    Name Number
    d mm Rp0,2 MPa min. Rm MPa A % min. Z % min. KV2 J min.
    25CrMo4 1.7218 +QT d ≤ 100 440 600 to 750 18 60 60
    100< di 150 420 600 to 750 18 60 45
    • a +AT = solution annealed; +C = cold work hardened; +N = normalized; +NT = normalized and tempered; +P = precipitation hardened;
    • +QT = quenched and tempered; +WW = warm worked (see Annex B).
    • b Products made of steel grades and these final heat treatment conditions support the Essential Safety Requirements of Directive 97/23/EC, see Annex 1, 7.5 of this directive.
    • c For rectangular cross-sections "d" will be replaced by "b" (see Figure 1).

    EN 10269 25CrMo4 Proof strength

    Minimum 0,2 %-proof strength values at elevated temperature of steels in delivery conditions which support the Essential Safety Requirements of Directive 97/23/EC d

    Material designation Heat treatment conditiona Diameter e d mm Minimum 0,2 %-proof strength Rp0,
    2 in MPa at a temperature (in °C) of:
    Name Number 50 100 150 200 250 300 350 400 450 500 550 600 650
    25CrMo4 1.7218 +QT d ≤ 100 435*) 428*) 420*) 412 392 363 333 304 275 235 - - -
    100 < d ≤ 150 414*) 403*) 393*) 382 372 344 324 294 265 226 - - -
    • a +AT = solution annealed; +C = cold work hardened; +N = normalized; +NT = normalized and tempered; +P = precipitation hardened; +QT = quenched and tempered; +WW = warm worked (see Annex B).
    • b This steel grade is generally not applied in the creep range.
    • c Values in brackets signify that the steel is not intended for use (and testing) at those temperatures.
    • d Products made to these steel grades and these final heat treatment conditions support the Essential Safety Requirements of Directive 97/23/EC; see Annex 1, 7.5 of this directive.
    • e For rectangular cross sections "d" will be replaced by "b" (see Figure 1).
    • *) Values calculated by linear interpolation.

    EN 10269 25CrMo4 Impact Energy

    Minimum impact energy (longitudinal direction) at low temperature of steels in delivery conditions which support the Essential Safety Requirements of Directive 97/23/EC b

    Material designation Heat treatment conditiona Diameter e d mm Minimum impact energy KV2 in J c
    (ISO-V test piece) at a test temperature in °C of:
    Name Number -270 -196 -160 -140 -120 -110 -100 -90 -80 -70 -60 -50 -40 -20 0 +20
    25CrMo4 1.7218 +QT d ≤ 60 - - - - - - - - - - 40 40 45 50 - 60
    60 < d ≤ 100 - - - - - - - - - - 40 40 50 - 60
    • a +AT = solution annealed; +C = cold work hardened; +N = normalized; +NT = normalized and tempered; +P = precipitation hardened; +QT = quenched and tempered; +WW = warm worked (see Annex B).
    • b Products made to these steel grades and these final heat treatment conditions support the Essential Safety Requirements of Directive 97/23/EC; see Annex 1, 7.5 of this directive.
    • c Average of 3 test results.
    • d Steel grade 1.4980 may be ordered for cryogenic purposes with impact values of 50 J at -270 °C, 60 J at -196 °C and 70 J at 20 °C.
    • e For rectangular cross sections "d" will be replaced by "b"
    Specifications
    Surface Treatments
    Certifications
    About Us
    Questions? Contact us.
    Showcase of our Microsites.
    Satisfaction Survey

    survey

    TUVRheinland CRETIFIED

    © TorqBolt P(Ltd) · Built with in INDIA.